Jetex are probably the U.K's leading supplier of universal exhaust parts for road, race or rally use. Parts are available with diameters of 1.75"(45mm) to 5" (127mm) in either stainless or aluminised/mild steel. Unique silencer fabrication allows 2" boxes to withstand temperatures of up to 600 degrees centigrade (for normal road conditions), while our 2.5", 3" and 3.5" boxes can withstand temperatures of up to 800 degrees centigrade (for higher powered engines and when used for race and rally applications).

Choose from a wide range of pipework, bends, silencer boxes, adaptors and tailpipes to construct an almost endless variety of free-flowing, power enhancing custom exhausts to suit your own unique application. Together with our range of Sports Catalysts, Jetex offer the total solution for road or race conditions. Our recently added 4 inch and 5 inch exhaust parts can be used for truck exhausts, and are ideal for extreme performance applications such as drag racing.

Straight Lengths and Bends

  • View Custom Parts Catalogue

  • Straight Lengths: Available in 1.75", 2", 2.5", 3", 3.5", 4" and 5" diameters. Mild or stainless steel. 1000mm or 500mm lengths. Pipework dimensions are outside diameter. One end is flared/slotted.
    Click for example

  • Mandrel Bends: Available in 1.75", 2", 2.5", 3", 3.5", 4" and 5" diameters. Mild or stainless steel. 30, 45, 60 or 90 degree angles. Pipework dimensions are outside diameter. One end is flared/slotted.
    Click for example

  • Tight Bends: Available in 1.75", 2", 2.5", 3", 3.5", 4" and 5" diameters. Mild or stainless steel. These bends are constructed using two pressed plates welded together Pipework dimensions are outside diameter. There are no flared ends with these parts.
    Click for example

  • 180 Degree Bends: Available in 1.75", 2", 2.5" and 3" diameters. Mild or Stainless steel. These are mandrel bends. Pipework dimensions are outside diameter. There are no flared ends with these parts.
    Click for example

  • Over Axle Bends: Available in 1.75", 2", 2.5" and 3" diameters. Mild or stainless steel. These are mandrel bends. Pipework dimensions are outside diameter. One end is flared/slotted.
    Click for example

Silencers

All silencer boxes are straight through absorption designed. Noise is reduced by absorption through a centre perforated tube. Consequently, there is less gas flow restriction and so back pressure is reduced, torque is increased and engine performance is enhanced.

Adaptors

  • View Custom Parts Catalogue

  • Double-End Sleeves: Available in 1.75", 2", 2.5", 3", 3.5", 4" and 5" diameter. Aluminised or stainless steel. Dimensions are outside diameter. Ends are not flared or slotted.
    Click for example

  • Stepped Sleeves: Available in 1.75", 2", 2.5", 3", 3.5", 4" and 5" diameter. Aluminised or stainless steel. Dimensions are outside diameter. Ends are not flared or slotted. 4" and 5" stepped sleeves have one step. All other diameter sleeves have 2 steps.
    Click for one step example
    Click for two step example

  • Y-Pieces: Available in 2", 2.25", 2.5", 3" and 3.5" diameter. Aluminised steel or stainless steel (2", 2.5", 3" and 3.5" only). Dimensions are outside diameter. Ends are not flared or slotted.
    Click for example

  • T-Pieces: Available in 2.5", 3" and 3.5" diameter. Aluminised or stainless steel. Dimensions are outside diameter. Ends are not flared or slotted.
    Click for example

  • X-Pieces: Ideal for V6 and V8 engines where each bank of exhaust gas should be brought together before separating again. Available in 2", 2.5" and 3" diameter. Stainless steel only. Dimensions are outside diameter. Ends are not flared or slotted.
    Click for example

Flexible Joints - ILOK

Our range of flex connectors is ideal for use before the catalytic converter where temperatures are high, engine movement is high and there is considerable gas noise.

  • View Custom Parts Catalogue

  • Can withstand up to 1100 degrees centigrade.

  • Interlock liner creates an air gap between the liner and bellows improving the cooling of the exhaust gas.

  • Flex connector prevents twisting of the exhaust pipework.

  • The main flex unit is made from stainless steel.

  • Each end is made of aluminised steel (except for 3" x 6" and 4" long ILOKS which are stainless steel) for extra corrosion resistance although as a result of high temperatues, corrosion is not an issue.

  • Each flex-connector is designed to allow pipework to slip inside each end and to be welded in position.
    Click to see internal lining

Flexible Joints - Polylock

Polylock flexible hosing is ideally used in low impact applications, such as where a particular bend is required but is not available in our range. These parts should be used further towards the back of the exhaust and in low stress conditions.

Flexible Joints - Compensators

Compensators prevent fracture between the downpipe and the rest of the exhaust system.

Flanges

Universal Backboxes

Our range of universal back boxes can be fitted in conjunction with our 2", 2.5" or 3" range of parts, or fitted to an existing exhaust system. Please note that these backboxes have to be adapted to suit an existing exhaust and will not fit straight on. However, by using adaptors from our custom range, this can easily be rectified. Tailpipe styles include Twin Round 57mm, Round 100mm, Round 100mm slash, Round 114mm, Round 114mm slash and Oval 90x120mm.

Universal Tailtrims

To finish off a custom exhaust or to improve the look of a standard exhaust system, Jetex offer a wide range of tailtrims (round, oval, square, slash-cut and many more) to fit 1.75" to 3.5" pipe diameters. We offer clamp-on tailtrims or weldable tailtrims.

Pipe Spacers

These small, but very useful mild steel parts allow two pipes to be joined together by filling in the space between them.

Lambda Fittings

Lambda bosses are available in mild or stainless steel. Plug is made from chrome plated mild steel.

Fittings

Jetex offer a wide variety of fittings to allow parts to be hung correctly under the car.

Decibel Reducers

Ideal for sound reduction in 2", 2.5" and 3" pipework. Decibel reducers should be placed inside a minimum of 300mm length of tubing and self tapped or welded in place. A cost effective method of sound damping.

 

Jetex Exhausts Ltd, Unit 25 The Waterways, Stratford-upon-Avon, Warwickshire, CV37 0AW

Tel: ++44 (0) 1789 298989 | Fax: ++44 (0) 1789 414463 | ©Jetex Exhausts Ltd 2013

Performance Exhausts
Custom Exhaust Parts
Performance Air Filters
Catalytic Converters
Catalogue Search by Part Number
Navigation